How To Set Up A Bow And Arrow
Doing your own custom bow build tin can be pretty scary if y'all've never done it before. In this video, as well as the article accompanying it, we'll cover what tools you need and how to supercede & install everything to set upward your new compound bow.
If you don't want to read through step by step, y'all tin check out our footstep-by-step bow build in the video beneath:
What You Need
To supplant and install everything on your bow, there are a number of tools that y'all'll need. And just a disclaimer – if you don't feel comfortable doing this, or are worried about messing upward your new bow, take it to your local store. It'southward always better to be prophylactic than sorry, especially with a bow that yous've invested a lot of money and fourth dimension into.
Here'south the full list of tools that you'll need to set up your own compound bow:
- Bow Press
- Bow Vise
- Draw Lath
- Allen Keys
- Tape Measure
- Light amplification by stimulated emission of radiation middle shot tool (optional)
- Leveling Tools
- Bow String Serving Fabric
- Cord Loop Material
- Blue Threadlocker (optional)
- Scissors
- Pocket Knife or Razor Bract
- Lighter
- D-Loop Pliers (or needle-nose pliers)
Stride 1 - Replacing Stock Cord & Cables
There's no doubtfulness that the stock string and cables that come with a new bow tin get the job done. Just with all the clothing and tear that our bows go through during the summertime do sessions, and the long hunting season, we want the best string possible.
We've been using ABB bowstrings for a few years now and take yet to accept whatever issues. With all the technology, research, and testing that's gone into their Platinum Series strings, this is a bowstring that tin final v+ years with ease. And when it comes to removing and replace the string and cables, it may seem daunting at first, simply it'southward relatively simple as long as yous have the right tools.
The first step is to go your bow into a bow printing, and relieve some of the tension that'south on the strings. With the yoke system that the V3 has, we needed to remove the string and cables, then de-printing the bow all the way out.
If this is one of the first times yous're doing this, nosotros'd suggest taking pictures of your string and cables. Especially at the roller guard and around your cams, but to make sure that y'all put everything back into the right spots in one case yous're all set.
Some other tip to keep in heed is to hold onto the stock cord and cables, but in instance an accident occurs sometime down the road. You don't desire to be halfway through the flavor and run into an event with your bow that requires the string to be replaced, thus leaving you lot unable to hunt for several days or weeks.
In gild to switch out the yoke cables on your bow, you take to de-press the bow all the style out and take it out of the press. Once that's done, it's time to movement over to a counter top to remove the cams from the limbs. The easiest way to remove a cam is to disengage one of the allen screws, and gently tap out the beam from that side, instead of removing both allen screws.
After y'all tap out the axles, you can bandy out the yoke cables for the new ones. And then you just need to put the cams back onto the bow and put it back into the printing to showtime getting the new string and cables onto information technology.
Earlier taking all the tension off of the limbs, make certain to reference your previous pictures and watch the string and cables to make certain everything is going back into the correct spots. Luckily with a lot of the recent bows, both cables are the same length and yous don't demand to worry about which is the meridian or bottom.
Just like that, with a little assistance from a bow press and some allen keys, y'all've got your custom string installed. At present that the bow has it'south new string and is removed from the bow printing, it'due south time to go over to your bow vise and start getting ready to install your remainder.
Step 2 - Installing The Residue & Finding Your Center Shot
Later your string is installed, put your bow in a vise and get everything perfectly level. One time your leveled off, mount your residuum to the riser of the bow. Every bow manufacturer uses the same size hole for the rest, so you don't need to worry about it fitting or non.
One time your remainder is deeply mounted to the riser, nosotros need to encounter if there are whatever horizontal adjustments we need to make to the residuum. For quite a while now, just virtually every Mathews bow has the center shot at the aforementioned distance about xiii/xvi″ from the riser. So we're going to start there and grab an arrow to run into if we need to make any other adjustments.
With the Van Handle arrow level nosotros accept, it comes with a screw-in peg that mounts on to where your stabilizer will go. We're able to apply the arrow tool to figure out if there are whatever other horizontal, or x-axis, adjustments that are needed.
In one case the x-axis is set, we're going to level out the arrow and see where it'south sitting. When you have the arrow sitting level, accept a wait at the hole where your rest is mounted, as the arrow should fun directly through the heart of that hole. Information technology'due south often chosen the "Berger Hole" and is the exact center of the bows riser.
You'll want to become your arrow as shut to level equally you tin can while running through the eye of the Berger Hole. Then if it's sitting below that hole when level, you should adjust your balance until it'southward perfect. You lot tin can even go out the arrow slightly nock high if you are using a drib-away rest.
After yous get your arrow level and lined upwardly with everything, take your serving material and necktie a nock fix higher up the nock. You can necktie information technology in a few different ways, in that location really is no wrong knot every bit long every bit there's no nock pinch occurring. Best exercise is to tie in 2-four knots max as at that place's no need to tie whatsoever more that.
One time you've got the superlative nock set tied in, motility to the lesser just make sure that you're using whatever nock you're planning to hunt with. There's nothing worse than getting your nock sets and D-Loop tied in, but to realize that your lighted nocks that y'all'll chase with are slightly bigger than your regular nocks. Then keep that in listen when tying the nock sets!
After your nock sets are in, you lot can just burn off the loose ends to go along information technology tight in place. Always keep the flame away from the balance of your string. Then if needed, put the bow dorsum into the bow press and so that the flame goes up abroad from your cord. A burnt or melted string volition without a doubt ruin your twenty-four hours and price y'all the toll of a new cord.
Step three - Install The Peep Sight & Necktie The D-Loop
Now that the nock sets are in and you've got the center shot, it'south fourth dimension to get the peep sight prepare. If you lot're thinking, "Why didn't they tie on a D-Loop afterward tying the nock sets?" Then you lot're non solitary. We actually near starting to tie on the D-Loop before realizing that it can be a time consuming error if yous set it before putting the peep sight in.
So put your bow back into the printing and accept a little tension off the string. If you're lucky plenty to take some other bow laying around with the same or similar axle-to-axle length, you can measure the distance from D-Loop to the peep sight to go an idea of where it volition be. But every string manufacturer volition have a small piece of serving tied on so that you lot can put the peep in properly.
When installing a peep sight, it's possible that the proper spot it sits may leave the peep sight facing the incorrect direction. You can fix this by putting in or taking out twists of the string. And one time you've got the peep sight ready, don't tie it in right away, but move on to the D-Loop.
Tying in a D-Loop is a pretty easy affair to do, and there'south hundreds of videos and articles that can show you how to do it, like this one – world wide web.bowhunting.com/blog/tie-d-loop/
Now that the D-Loop is tied, don't worry if you finish up needing to re-tie it at some point. We'll ordinarily go through a few D-Loops before getting the exact right spot and size.
Later installing the D-Loop and tightening it downwards, mount your sight to the riser. Once your sight is mounted, yous can describe your bow to check the peep sight alignment. You may need to move your peep sight up or down a footling bit, and if that is needed, you may somewhen need to add or remove another twist out of your string so the peep sight stays in-line.
After you check the peep sight and set information technology in the right spot, you tin now necktie in your peep sight. Just like a D-Loop and nock sets, tying in a peep sight tin can be done in a multitude of means. Check out this video from our friend PJ Reilly with Lancaster Archery, on how to tie one – www.youtube.com/watch?v=T8MXLFsjFSY
Step four - Setting Up A Drop-Away Residue
At present that we're almost ready to shoot the bow, we demand to gear up up the residue. If yous've got a static rest like a whisker beige, then you're basically prepare to get. Just if you lot've got a drib-away rest, then in that location'south ane last step that tin can't be forgotten.
The HHA Virtus rest that we're using, needs to be threaded between the downward pulling cable. So we need to get the bow back into the bow printing and take a little tension off the string and cables. What we'll commonly do is have the D-Loop material that comes with the rest, and fire the finish if yous haven't already.
One time the bow is pressed and ready, yous'll need to split the cable strings just below the serving. If you accept a two colored cord, this should exist easy. Only if your string is all one color, this might exist a little harder for you.
Nosotros will eventually tie a couple knots to make sure this stays in place, but for now let's take the bow out of the printing. The Virtus has a set up spiral to easily adjust the length of the string, and you should loosen that upward a chip if your rest has ane.
The way we set the altitude on this string is by loosening up that set up screw a footling, and drawing the bow back. This should pull the cord through by the stopper and set it at the right length. After yous let your bow down, pull that string simply a little flake tighter, then tighten downward that set spiral. Bank check the rest by drawing your bow back a few more than times to see if the residue comes all the way into the proper position.
Once that's done, you're ready to shoot! Just popular a stabilizer on and start launching arrows.
Decision
Source: https://www.bowhunting.com/bowhunt101/how-to-setup-a-compound-bow/
0 Response to "How To Set Up A Bow And Arrow"
Post a Comment